1963 Ford Fairlane LMS, by MCB Motorsport

[mrchevyblack]

Hi everybody, i built a lot of Factory Stock and drag racing machine!!!! But now i'm back on the short tracker market!!!!

There the new beast!!!

An 1963 Ford Fairlane LMS,

Body is resin from a friend of everyone here, Fred of Fred Resin WorkShop FRW!!!
with all other patys just coming back from the chrome shop...


The donor kit for the chassis, engine and lot of other parts it's that one from AMT/Model King, 1972 Ford Torino, this kit offer the possibility to built as small 351 or or 429 big block!!! Maybe then i'm choose the small block engine!!


And for finish, i use a lot of aftermarkets parts, my trade mark, like this tire from Plastic Performance Product



CHAPTER 2........[/color][/i][/b]

MCB Motorsport
SHOP REPORT #2 18/02/2013

It's start again, i'm coming back to my Fairlane, i assembled the chassis and roll cage today. And he still to have of work!!
I try to finish for my show in Granby on March 17th but the one then go to the NNL East in April the Fairlane was on the MCB Motorsport stand!



Hi added two little bracket on the radiator support toa better maintain of the body in place.


Hi relocated the front cage mount, i still to didn't like! I continu my work on that! Nice view of the body on to the chassis!




Hi remove the kit fuel cell to replace by an resin one!!


Nice with the hood in place!


Stay tuned for the next SHOP REPORT soonelly on this forum...

[mrchevyblack]

MCB Motorsport
SHOP REPORT 2013/02/19

MY built continu, today i still worked on my chassis. I install some additional hood support and scratchbuilt a bracket for the dasd board!


This is permit to maintain in correct place the dash, becaus when you play with resin this need to made a lot modification and , of course, a lot of test fit.


Also worked on the two front cage mount, i use Evergreen rod, he look bettrte now!





This side view permited to see then new cage mounting fir very more better with squared Fairlane body!


After i worked to extended the rear section of the chassis then joint the rear bumper!




That's it for today, don't mist the next SHOP REPORT on this forum...

[mrchevyblack]

MCB Motorsports
SHOP REPORT 2013/02/20

Ok! This one it'S a little one, i just worked on the Fuel cell support, the fuel was in resin from Fred Resin Workshop.
À partir de tige d'Evergreen je me suis fabriquer ce support!



Heri he is with hose ans gaz cap!



I like to showint to you some other resin parts then previeuw to go on my Fairlane project!
I choose a set of wheels from FRW with Plastic Performance Product.


The rear end, of course it'S an "Quick Change" type.


The oil pan and carburator.


Stay tuned for the next SHOP REPORT soonelly on this forum!!!

[mrchevyblack]

MCB Motorsports
SHOP REPORT 2013/02/24

The project didn't stop, always goes up front!!!!

I install a new Quick change rear end


First i have to remove the older ome from the suspension part.


I remove everything, i just keep the suspensions.



With mt Dremel i worked on my part to made an half round fopr the differential housing....


And now he fit perfectely....


I use a super glue to gluing in place the suspension, for the application i use my faviorite tool, a touth pick...


Everything is ok! and right on his place!!!


I give some times to a glue for drying....


Step #2;
With the nice resin part like my fuel cell this need then openned the rear trunk.


When is open, i install fours supports pin to maintasin in place ther truck cover


I know then i have a niciest gas cap, but he is too much higner, this need then i scratchbuilt one for Evergreen rod


Ther my all new gas cap in place........


And the trunk copver close perfectly now!



That is for today......


Stay tuned for the next SHOP REPORT soonely on this forum...